Tags

next-20200319

next-20200318

This is the 5.5.10 stable release

This is the 5.4.26 stable release

This is the 4.19.111 stable release

Qualcomm driver updates for v5.7

This adds a new library for subscribing to notifications about
protection domains being stated and stopped and the integration of this
with the APR driver. It also contains fixes and cleanups for AOSS
driver, socinfo and rpmh.

Qualcomm ARM defconfig updates for v5.7

Enable QRTR and the Broadcomm bluetooth driver in the qcom_defconfig,
for usage on the 8974 devices.

Qualcomm ARM dts updates for v5.7

This adds Bluetooth support on Nexus 5, USB on Xperia Z1 and defines
gpio-ranges throughout the various gpio-controllers.

Qualcomm ARM64 defconfig updates for v5.7

Enable SDM845 audio, display and gpu related configs and the Truly
NT35597 panel driver, all relevant for various SDM845 based boards.
Enable IPQ6018 clocks and pinctrl and the pmic vibrator driver for
PM8916.

Qualcomm ARM64 DT updates for v5.7

This brings initial support for the SM8250 and IPQ6018 platforms.

SDM845 gets audio, PCIe and IP-accelerator support, and the interconnect
providers are refactored. The Lenovo Yoga C630 has audio enabled and the
DB845c has PCIe, analog audio and low-speed interfaces enabled. The
SDM845 MTP has its display enabled and firmware location updated to
match linux-firmware.

SC7180 gains CPU topology and power properties. Interconnect providers,
eMMC, SD-card, multimedia clocks, display, Bluetooth, Venus are added.
Critical trip points are added as well as various fixes.

For MSM8916 FastRPC support is added, ETM power management and reserved
memory for Samsung A2015 are corrected.

MSM8996 switches to generic QMP phy driver for its UFS support. MSM8998
temporarily disables part of Coresight to boot without
clk_ignore_unused.  CEQ for eMMC on QCS404 is enabled.

Fixes throughout the platforms to fix binding compliance, correct
compatibles for SDHCI nodes and add gpio-ranges.

next-20200317

This is the 4.19.110 stable release

next-20200316

Linux 5.6-rc6

wireless-drivers fixes for v5.6

Third, and hopefully last, set of fixes for v5.6.

iwlwifi

* fix a locking issue in time events handling

* a fix in rate-scaling

* fix for a potential NULL pointer deref

* enable antenna diversity in some devices that were erroneously not doing it

* allow FW dumps to continue when the FW is stuck

* a fix in the HE capabilities handling

* another fix for FW dumps where we were reading wrong addresses

* fix link in MAINTAINERS file

rtlwifi

* fix regression causing connect issues in v5.4

wlcore

* remove merge damage which luckily didn't have any impact on functionality

next-20200313

Allwinner Fixes for 5.6 - part 2

This follows up on the previous 5.6 fixes tag with a fix for the A33
Security System (crypto offloading hardware). The hardware was found
to not be compatible with existing hardware and a new compatible was
needed.

The driver change was picked up right before the previous -rc6 and
the DT bindings and DT changes were not picked up. The goal is to have
all the changes in the same release, that is v5.6.

Allwinner Device Tree Changes for v5.7

A fairly large set of changes for v5.7, including some new devices.

SoC specific changes:

  - SPI on H6 SoC enabled
  - Thermal sensor on R40 SoC enabled
  - Deinterlace core hardware on A64 SoC enabled
  - Redundant assigned-clocks properties removed
    - required clock rates are now enforced by drivers
  - LVDS panel support on A20 SoC enabled
  - PMU compatible fixed for H5 and H6 SoCs
  - Thermal trip points added for A83T and H5 SoCs
  - (Image) Rotation core hardware on A83T and A64 SoCs enabled

Device specific changes:

  - Pine64 PineTab and PinePhone added
  - Various cleanups and improvements for Pine64 PineBook
  - GPIO pin bank regulator supplies added for A64-OlinXino
  - eMMC enabled on Orange Pi 3
  - PocketBook Touch Lux 3 added
  - Linutronix Testbox v2 added
  - Ethernet enabled on Orange Pi One Plus
  - HDMI enabled on H6-based Orange Pi boards

Allwinner Core Changes for v5.7

Just one change for our mach code for including the correct clk header.