Tags

ASoC: Fixes for v5.0

A few small fixes, a driver fix for Samsung, a fix for refcounting of
of_nodes in the simple-card driver that triggered on a lot of systems
and a fix for topology error handling.

Prep patches + headers for the mei-hdcp/i915 component interfaces

Also contains the prep work in the component helpers plus adjustements
for the snd-hda/i915 component interface.

Plus one small static inline in the drm_hdcp.h header that both i915
and mei_hdcp will need.

wireless-drivers fixes for 5.0

Hopefully the last set of fixes for 5.0, only fix this time.

mt76

* fix regression with resume on mt76x0u USB devices

Linux 5.0-rc7

Just a few fixes this time:
 * mesh rhashtable fixes from Herbert
 * a small error path fix when starting AP interfaces

This is the 4.20.10 stable release

This is the 4.19.23 stable release

This is the 4.14.101 stable release

This is the 4.9.158 stable release

This is the 4.20.9 stable release

This is the 4.19.22 stable release

This is the 4.14.100 stable release

This is the 4.9.157 stable release

Second set of new device support, features and cleanup for IIO in the 5.1 cycle.

There are a few late breaking fixes in here that weren't worth trying to
rush into 5.0 as they have been with us for quite a while.

New device support
* ad7476
  - add support for TI ADS786X parts that are compatible with this Analog
    Devices driver. Good to see some simple devices are so similar.
* Ingenic jz47xx SoC ADCs
  - new driver and bindings
* Plantower PMS7003 partical sensor
  - new driver and bindings including vendor prefix.
* TI DAC7612
  - new driver and bindings for this dual DAC.

New features
* ad7768-1
  - Sampling frequency control
* bmi160
  - Data ready trigger support, including open-drain dt binding.

Cleanup / minor fixes.
* Analog Device DACs
  - Fix some inconsistent licenses.  These are only ones where there were
    two different license marked in the same file, and hence were previously
    unclear.
* ads124s08
  - Spelling fix.
* adxl345
  - Parameter alignement tidy up.
* bmi160
  - SPDX
  - correct a note on the types of supported interrupts which was too strict.
  - use iio_pollfunc_store_time to grab an earlier timestamp.
  - use if (ret) instead of if (ret < 0) to be consistent whilst simplifying
    some handling where ret was effectively getting written to 0 even though
    it was always already 0.
* exynos_adc
  - Fix a null pointer dereference on unbind.
  - Fix number of channels on Exynos4x12 devices to be 4 rather than 8.
* lpc32xx-adc
  - Move DT bindings doc out of staging. Oops, I missed this one when
    moving the driver.
  - SPDX.
* npcm-adc
  - drop documentation of reset node as going to be done differently.
    It's a new driver this cycle so no need to support the previous
    binding going forwards.
* sps30
  - Fix an issue with a loop timeout test that meant it would never identify
    a timeout.
  - Mark deliberate switch fall throughs.

This is the 4.20.8 stable release

This is the 4.19.21 stable release

This is the 4.14.99 stable release

This is the 4.9.156 stable release

phy: for 5.1

  *) Add a new driver to support Armada 3700 COMPHY IP (supports SATA, USB3,
     PCIe)
  *) Add a new driver to support Armada UTMI PHY
  *) Add a new driver to support Cadence D-PHY
  *) Extend omap-usb2 PHY driver to be used for AM654 USB2 PHY
  *) Extend qcom-qmp PHY driver to be used for UFS PHY and USB3 PHY in Qualcomm
     MSM8998
  *) Extend qcom-qusb2 PHY driver to support QUSB2 PHY in Qualcomm MSM8998
  *) Remove module specific code that is present for drivers that can be only
     built-in
  *) Allow Freescale IMX8MQ USB to be used for multiple SoCs and not just
     i.MX8MQ
  *) Cleanups such as switch to SPDX identifier, use readl_poll_timeout macro,
     remove unused headers etc.,

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>